- #Ten tec pegasus control software 64 Bit
- #Ten tec pegasus control software full
- #Ten tec pegasus control software software
- #Ten tec pegasus control software trial
- #Ten tec pegasus control software plus
Conventional Fast, Medium and Slow modes are familiar but the Programmable mode is groundbreaking. USB, LSB, ISB, CW, AM, Synchronous AM and FM are built in. All filters have shape factor of 1.5 1 or better 6 to 60 dB. bandwidths from 100 Hz to 16 kHz are included. filters, AGC remaining 40 dB, adjustable BFO, passband tuning and noise blanker. Everything else is accomplished in DSP including all mode detection, I.F. High dynamic range analog stages provide 1st, 2nd and 3rd I.F.s and 80 dB of AGC where signals then pass through analog to digital converters.
#Ten tec pegasus control software software
Powerful, specialized DSP microprocessors replace many of the discrete circuits with intensive software containing over 60,000 lines of code. These designs utilize fewer analog circuits than traditional receivers. The performance level of receivers in this class is possible only through extensive use of Digital Signal Processing. The RX 340 is a laboratory quality instrument in its ability to quantify the amplitude and frequency characteristics of signals and receivers. All three displays are blue green vacuum fluorescent and provide unparalleled contrast and readability. Tunable from 5 kHz to 30 MHz, it provides tuning steps and display resolution of 1 Hz. DSP brings the performance and repeatability of expensive military grade communications receivers into the price range of top end commercial receivers for shortwave listeners. Kick off users that are logged on but not there.Īdded remembering antenna setting between program session for the K3.Īdded using RIT in the calculation for VFO A for the Perseus panadapter.The TEN-TEC RX 340 is a multi mode, general coverage synthesized receiver utilizing extensive Digital Signal Processing. To set transmit and receive via software commands.Īdded support for the K3 with sub-receiver to run split modeįor remote base operation, added “exiting the server” as a way to Interface for transmit and receive commands. Restored course CW speed slider that disappeared in previous version.Īdded support on the third party logging program virtual comport (13) Remote Mirrored Radio Operation for Two Identical Icom Radios.Ĭhanges from version 4.05 to version 4.06Īdded remembering the monitor state between program sessions for (12) All N4PY software now build with Microsoft Visual Studio C++ 2010.
#Ten tec pegasus control software plus
(11) The Pegasus Plus program now supports the Tentec RX-400 HF/VHF/UHF transceiver.
#Ten tec pegasus control software full
(10) The Icom program now has full support for the IC-9100 transceiver. (9) The Pegasus Plus program now has support for the Alpha 87A amplifier. (8) The Pegasus Plus program now has support for the ADR2200 antenna switch. This panadapter has a much simpler installation as no virtual comports are required. (7) All Programs now have support for TRX-Pan with LP-Pan.
(5) All programs now have support for the RFSpace SDR-IQ panadapter. (4) The Icom program now has full support for a standalone Perseus receiver. This is most useful when running a client-server setup. (3) All programs now have a method for receiving CW characters from contesting programs. (2) All programs now have a total of three external comports to allow panadapters, CWSkimmer, and external logging programs to run at the same time without LP Bridge. (1) All programs now have support for the Perseus receiver as a Panadapter.
#Ten tec pegasus control software trial
If you decide you want to use the program after the trial period, please visit N4PY’s website. N4PY have older versions on the “previous versions” page that will run on Windows 95, 98, ME, and 2000.
#Ten tec pegasus control software 64 Bit
And don’t hesitate to ask any questions you might have by sending an email to me.Īll N4PY software programs run on windows operating systems Windows XP, Vista, Windows 7, and Windows 8 (including the 64 bit versions of XP, Vista, and Windows 7 and 8). Just download the software you are interested in to get a 10 day free trial. All N4PY Software will run for 10 days without a password. There are many reviews of this software on Eham. N4PY Software has been in existence since 1999.
N4PY offers rig control software for a wide variety of receivers from the Elecraft K3 to the Ten Tec RX 320 receiver. N4PY Software is your source for high quality, effective rig control software for your transceiver.
0 kommentar(er)
